Theben Tr 610 S User Manual
- Theben Tr 610 S Manuale Italiano
- Theben Tr 610 S Manual
- Theben Tr 610 S Instructions
- Theben Tr 610 S User Manual English
- Theben Timer Tr 610 Manual
- Theben Tr 610 S Operating Instructions
Crossing: Normally an OBELISK which, for example, was programmed for a TR 610 top2, can also only be used in a TR 610 top2. The transfer e.g. Of the switching times of a TR 610 top2 to the second channel in a TR 622 top2 (Crossing) can be performed using a diversion via the OBELISK top2 PC software. In this case the OBELISK can be. Sep 05, 2017 Learn in this video how to program, change or delete switching times at a digital time switch of the top2 or top3 series. Additional information at https://w. TR 610 top3 6100130 TR 612 top3 6120130. Call the Theben Hotline. L Have the serial number ready. OPTIONS NO PIN WITH PIN CURRENT PIN NEW PIN 00 00 OPERATING HOURS LCD ILLU-MINATION LANGUAGE PIN FACTORY SETTINGS INFO END u u MENU Setting manual or permanent switching Manual or permanent switching can be set via the menu in MANUAL.
Page 1 of 2
Document #1200368.doc Rev 4
01/17/07
HAZARDOUS VOLTAGE:
Risk of electric shock. Can
cause injury or death. This
device may be connected to
more than one branch circuit.
Disconnect all branch circuits
WARNING
STEFFES CORPORATION
THEBEN MODEL “TR610 TOP” TIME CLOCK
SETTING INSTRUCTIONS
Item #1301007R (120V Clock) and Item #1301008R (240V Clock)
NOTE: The Theben time clock is equipped with a lithium battery with an
approximate 4year power reserve.
Throughout the programming of the time clock, if there is approximately 90 seconds of
inactivity (no buttons are pushed), the display will automatically reset to normal
operation. If the clock resets and the program information you are entering or editing
is not stored, the time clock will default to the previous settings. The new information
will have to be reprogrammed.
A. SETTING THE TIME CLOCK
Theben Tr 610 S Manuale Italiano
1.
The time clock is delivered in a 'sleep' mode. To activate without a service
voltage, press and release one of the four buttons.
2.
Select the national language by pressing the '◄' or '►' button until the desired language is
flashing. Press 'OK' to save the selection.
3.
To set the year, press the '◄' or '►' button until the current year is displayed. Press 'OK' to
save.
LG Pick LG Tub Cleaning - Front Load & Top Load Washer LG TUB CLEAN is a maintenance routine that is recommended to keep your washing machine in optimal performance. This help library content will show you how to clean your tub, dispenser, water inlet filters and the exterior part of your mach. Lg Truebalance Washer Manual We purchased a brand new LG washer and dryer from Home Depot in November LG True Balance Washer - I agree with every negative review I have read. WM2801HLA Washer pdf manual download. TrueBalance™ Anti-Vibration System. SteamFresh™ Washer LG WM2032HW Owner's Manual. LG Washing Machine Owner's. View and Download LG WT5070CW owner's manual online. Ultra-Large Capacity High Efficiency Top Load Washer with WaveForce™. WT5070CW Washer pdf manual download. Also for: Wt5170hw, Wt5170hv, Wt1201cw, Wt1201cv, Wt1101cw. Lg true balance washer user manual. Owner's manual; LG WM3632H Owner's Manual. Washer LG WM3001HWA User's Manual & Installation Instructions. Ultra-capacity steamwasher (72 pages). If sound continues, washer is probably out of balance. Page 22 Do not over load. Check that the washer is draining properly to extract adequate water from the load. Clothes load is too small to. Laundry manuals and free pdf instructions. Find the user manual you need for your laundry appliances and more at ManualsOnline.
4.
Set the month by using the '◄' or '►' button until the current month is displayed. Press
'OK' to select.
5.
Set the day of the month using the '◄' or '►' button until the day of the month is displayed.
This display will show the month selected, followed by the day (09.01). Press 'OK' to select.
6.
Set the current hour of the day using the '◄' or '►' button until the hour is displayed. Make
sure the correct am/pm hour is selected. Press 'OK'.
7.
Set the minutes using the '◄' or '►' button. Press 'OK' to save.
NOTE: At this point, the time clock should continue with setup of daylight savings time; however,
the clock may return to the normal operating mode and skip the daylight savings section. If
this occurs, press the 'MENU' button until the “¹” is flashing at the top of the display.
Press 'OK' and repeat Steps 38.
8.
To set whether or not daylight savings time (DST) will be utilized, press the '►' button until 'SUM/WIN' is
displayed. Press 'OK'.
Theben Tr 610 S Manual
a. With Daylight Savings Time
¨
Press the '►' button until 'WITH S/W' is displayed. Press 'OK'.
¨
Use the '►' button until 'USA/CAN' is displayed. Press 'OK'.
b. Without Daylight Savings Time
¨
Press the '►' button until 'NO SU/WI' is displayed. Press 'OK'.
9.
The clock will return to the time/status display and the day of the week should automatically be indicated by an
arrow (1 = Monday..7 = Sunday) at the bottom. Imac g3 manual download.
NOTE: If daylight savings time is to be recognized, a snowflake or a sun will appear in the clock
display. A snowflake indicates winter months (days between last Saturday in October and
first Sunday in April). A sun indicates summer months (days between first Saturday in April
and last Sunday in October).
B. SETTING THE CHARGE (ON) AND CONTROL (OFF) CYCLES
NOTE:
Start times for each charge (on) and control (off) cycle MUST be set. They DO NOT need to be set in
sequential order.
1.
Press the “MENU” button until 'Prog' is flashing in the upper portion of the display. Press 'OK'.
2.
Theben Tr 610 S Instructions
Use the '◄' or '►' button until 'NEW PROG' is flashing in the display. Press 'OK'. 'FREE' and a number will
automatically appear after a few seconds to indicate how many program locations are available. There are a total of
28 program locations available if no program settings have been entered.
Theben Tr 610 S User Manual English
3.
The clock will automatically display 'TIME ON' or 'TIME OFF' toward the top of the display. Below this, 'On' or 'Off'
will be flashing. Use the '◄' or '►' button until “Time ON” displays and press “OK” to set the charging period.
Reminder: “ON” is a charging cycle and “OFF” is a control cycle.